Hyper terminal
iTop 4412 boot log
OK
U-Boot 2010.03 (Mar 19 2018 - 23:52:03) for iTOP-4412 Android
APLL = 1000MHz, MPLL = 800MHz
ARM_CLOCK = 1000MHz
PMIC: S5M8767(VER5.0)
Board: iTOP-4412
DRAM: 1 GB
MMC: max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
max_emmc_clock:40 MHZ
Input CLK [ 50 MHz] is higher than limit [40 MHZ]
Set CLK to 40000 KHz
EMMC clock output: 40000 KHz
MMC0: 7456 MB
SD sclk_mmc is 400K HZ
eMMC OPEN Success.!!
!!!Notice!!!
!You must close eMMC boot Partition after all image writing!
!eMMC boot partition has continuity at image writing time.!
!So, Do not close boot partition, Before, all images is written.!
MMC read: dev # 0, block # 48, count 16 ...16 blocks read: OK
eMMC CLOSE Success.!!
Checking Boot Mode ... EMMC4.41
SYSTEM ENTER NORMAL BOOT MODE
Hit any key to stop autoboot: 0
reading kernel.. 1120, 12288
MMC read: dev # 0, block # 1120, count 12288 ...Rå=MÑ412 (id 0xe4412011)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[ 0.000000] audiocdclk: no parent clock specified
[ 0.000000] s3c_register_clksrc: clock armclk has no registers set
[ 0.000000] EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=350000000
[ 0.000000] EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=24000000
[ 0.000000] ACLK160=160000000, ACLK133=133333333, ACLK100=100000000
[ 0.000000] EXYNOS4: ACLK400=24000000 ACLK266=800000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll_user (6), rate is 100000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 200000000
[ 0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 41666666
[ 0.000000] sclk_pwi: source is xusbxti (1), rate is 1500000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c11bd000 s6752 r8192 d13728 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251650
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootfstype=ext4 init=/linuxrc console=ttySAC2,115200
[ 0.000000] log_buf_len: 524288
[ 0.000000] early log buf free: 127665(97%)
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 736MB 255MB = 991MB total
[ 0.000000] Memory: 613964k/613964k available, 400820k reserved, 261120K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfea00000 - 0xffe00000 ( 20 MB)
[ 0.000000] vmalloc : 0xee800000 - 0xf6000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xee000000 ( 736 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc003e000 ( 216 kB)
[ 0.000000] .text : 0xc003e000 - 0xc08d2000 (8784 kB)
[ 0.000000] .data : 0xc08d2000 - 0xc0976f80 ( 660 kB)
[ 0.000000] .bss : 0xc0977270 - 0xc09b3a90 ( 243 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:456
[ 0.000000] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[ 0.045000] pid_max: default: 32768 minimum: 301
[ 0.045000] Mount-cache hash table entries: 512
[ 0.045000] Initializing cgroup subsys debug
[ 0.045000] Initializing cgroup subsys cpuacct
[ 0.045000] Initializing cgroup subsys freezer
[ 0.045000] CPU: Testing write buffer coherency: ok
[ 0.045000] **********panic_dump_test****************
[ 0.045000] There is no valid panic information in memory
[ 0.045000] **************************
[ 0.045000] L310 cache controller enabled
[ 0.045000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[ 0.075000] CPU1: Booted secondary processor
[ 0.095000] CPU2: Booted secondary processor
[ 0.115000] CPU3: Booted secondary processor
[ 0.115000] Brought up 4 CPUs
[ 0.115000] SMP: Total of 4 processors activated (7969.17 BogoMIPS).
[ 0.120000] print_constraints: dummy:
[ 0.120000] NET: Registered protocol family 16
[ 0.120000] value1 = 1, value2 = 0, type = 0x2
[ 0.120000] value1 = 1, value2 = 0, type = 0x2
[ 1.125000] exynos4_pmu_init: PMU supports 4412(96)
[ 1.125000] S3C Power Management, Copyright 2004 Simtec Electronics
[ 1.125000] EXYNOS4: Initializing architecture
[ 1.125000] panic_file create OK !!
[ 1.125000] s3c-adc exynos4412-adc: attached adc driver
[ 1.125000] samsung-pd samsung-pd.0: power domain registered
[ 1.125000] samsung-pd samsung-pd.1: power domain registered
[ 1.125000] samsung-pd samsung-pd.2: power domain registered
[ 1.125000] samsung-pd samsung-pd.5: power domain registered
[ 1.125000] samsung-pd samsung-pd.4: power domain registered
[ 1.130000] samsung-pd samsung-pd.6: power domain registered
[ 1.130000] samsung-pd samsung-pd.7: power domain registered
[ 1.130000] s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
[ 1.130000] UMP: UMP device driver loaded
[ 1.145000] bio: create slab <bio-0> at 0
[ 1.145000] SCSI subsystem initialized
[ 1.145000] s3c64xx_spi_probe(969)
[ 1.145000] s3c64xx_spi_probe(1092)
[ 1.145000] s3c64xx_spi_probe(1113)
[ 1.150000] usbcore: registered new interface driver usbfs
[ 1.150000] usbcore: registered new interface driver hub
[ 1.150000] usbcore: registered new device driver usb
[ 1.150000] i2c-gpio i2c-gpio.0: using pins 42 (SDA) and 43 (SCL)
[ 1.150000] +s5m8767_pmic_probe()
[ 1.150000] print_constraints: vdd_mif range: 900 <--> 1100 mV at 1100 mV
[ 1.150000] print_constraints: vdd_arm range: 850 <--> 1450 mV at 1200 mV
[ 1.150000] print_constraints: vdd_int range: 875 <--> 1200 mV at 1000 mV
[ 1.155000] print_constraints: vdd_g3d range: 750 <--> 1500 mV at 1100 mV
[ 1.155000] print_constraints: vdd_m12 range: 750 <--> 1500 mV at 1200 mV
[ 1.155000] print_constraints: vdd12_5m range: 750 <--> 1500 mV at 1200 mV
[ 1.155000] print_constraints: vddf28_emmc range: 750 <--> 3000 mV at 2850 mV
[ 1.170000] print_constraints: VDDQ_M12: 1500 mV
[ 1.170000] print_constraints: VDD18_2M: 1800 mV
[ 1.170000] print_constraints: VDD10_MIPI: 1000 mV
[ 1.185000] print_constraints: VDD33_LCD: 3300 mV
[ 1.185000] print_constraints: VDD18_MIPI: 1800 mV
[ 1.195000] print_constraints: VDD33_UOTG: 3300 mV
[ 1.200000] print_constraints: VDD10_USH: 1000 mV
[ 1.200000] print_constraints: VDD18_HSIC: 1800 mV
[ 1.200000] print_constraints: VDDIOPERI_28: 3300 mV
[ 1.215000] print_constraints: DC33V_TP: 3300 mV
[ 1.215000] print_constraints: VDD28_CAM: 1800 mV
[ 1.215000] print_constraints: VDD28_AF: 2800 mV
[ 1.215000] print_constraints: VDDA28_2M: 2800 mV
[ 1.220000] print_constraints: VDD28_TF: 2800 mV
[ 1.230000] print_constraints: VDD33_A31: 3300 mV
[ 1.250000] print_constraints: VDD18_CAM: 1800 mV
[ 1.255000] print_constraints: VDD18_A31: 1800 mV
[ 1.255000] print_constraints: GPS_1V8: 1800 mV
[ 1.260000] print_constraints: DVDD12: 1200 mV
[ 1.260000] -s5m8767_pmic_probe()
[ 1.260000] s5m87xx 1-0066: S5M87xx MFD probe done!!!
[ 1.260000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 1.260000] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 1.260000] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[ 1.260000] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[ 1.260000] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 1.260000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 1.260000] Bluetooth: Core ver 2.16
[ 1.260000] NET: Registered protocol family 31
[ 1.260000] Bluetooth: HCI device and connection manager initialized
[ 1.260000] Bluetooth: HCI socket layer initialized
[ 1.260000] Bluetooth: L2CAP socket layer initialized
[ 1.260000] Bluetooth: SCO socket layer initialized
[ 1.260000] cfg80211: Calling CRDA to update world regulatory domain
[ 1.260000] Switching to clocksource mct-frc
[ 1.260461] Switched to NOHz mode on CPU #0
[ 1.260687] Switched to NOHz mode on CPU #3
[ 1.260694] Switched to NOHz mode on CPU #1
[ 1.260700] Switched to NOHz mode on CPU #2
[ 1.262006] NET: Registered protocol family 2
[ 1.262179] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.262811] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.264313] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 1.265139] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.265156] TCP reno registered
[ 1.265173] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.265211] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.265478] NET: Registered protocol family 1
[ 1.265690] PMU: registered new PMU device of type 0
[ 1.265838] Exynos4 : ARM Clock down on idle mode is enabled
[ 1.266714] regulator_consumer_probe: loading tc4-regulator-consumer
[ 1.266734] Register vdd_consumer_early_suspend done
[ 1.267351] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 1.267367] DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 1.267661] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 1.267677] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.267774] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 1.267790] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.275001] highmem bounce pool size: 64 pages
[ 1.275222] ashmem: initialized
[ 1.284223] fuse init (API version 7.16)
[ 1.284536] msgmni has been set to 689
[ 1.285189] io scheduler noop registered
[ 1.285202] io scheduler deadline registered
[ 1.285258] io scheduler cfq registered (default)
[ 1.286123] value1 = 1, value2 = 0, type = 0x2
[ 1.540046] (s3cfb_cfg_gpio, 98): BK_VDD_ON
[ 1.645083] (s3cfb_cfg_gpio, 120): LCD_PWDN ON
[ 1.646098]
[ 1.646102] CPU type:
[ 1.646112] Exynos 4412
[ 1.646123] value1 = 1, value2 = 0, type = 0x2
[ 1.646837] parent clock: 800000000, vclk: 6776000, vclk div: 118
[ 1.896509] (s3cfb_backlight_on, 363): LCD_PWM_ON
[ 1.901521] (s3cfb_backlight_on, 434): VGA_EN_ON
[ 1.901541] s3cfb s3cfb.0: registered successfully
[ 1.902198] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.230258] s5pv210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 16) is a S3C6400/10
[ 2.305062] s5pv210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 20) is a S3C6400/10
[ 2.385059] s5pv210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 24) is a S3C6400/10
[ 3.401770] console [ttySAC2] enabled
Ë
r¢rj
[ 3.624983] usbcore: registered new interface driver dm9601
[ 3.630269] usbcore: registered new interface driver dm9620
[ 3.635855] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.642303]
[ 3.642307]
[ 3.642309] [usb_host_phy_init]++++++++++++++
[ 3.649766] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 3.654807] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 3.661941] s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
[ 3.675040] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 3.679077] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice=0300
[ 3.687140] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.694341] usb usb1: New USB device Class: Class=9, SubClass=0, Protocol=0
[ 3.701284] usb usb1: Product: S5P EHCI Host Controller
[ 3.706491] usb usb1: Manufacturer: Linux 3.0.15 ehci_hcd
[ 3.711871] usb usb1: SerialNumber: s5p-ehci
[ 3.716624] hub 1-0:1.0: USB hub found
[ 3.719855] hub 1-0:1.0: 3 ports detected
[ 3.724434] usbcore: registered new interface driver cdc_acm
[ 3.729494] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.737478] Initializing USB Mass Storage driver...
[ 3.742479] usbcore: registered new interface driver usb-storage
[ 3.748328] USB Mass Storage support registered.
[ 3.753183] usbcore: registered new interface driver usbserial
[ 3.758745] usbserial: USB Serial Driver core
[ 3.763191] USB Serial support registered for GSM modem (1-port)
[ 3.769222] usbcore: registered new interface driver option
[ 3.774629] option: v0.7.2:USB Driver for GSM modems
[ 3.779780] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[ 3.779786] s3c-udc : version 15 March 2009
[ 3.793499] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 3.798919] android_usb gadget: Number of LUNs=3
[ 3.803517] lun0: LUN: removable file: (no medium)
[ 3.808378] lun1: LUN: removable file: (no medium)
[ 3.813238] lun2: LUN: removable file: (no medium)
[ 3.818371] android_usb gadget: android_usb ready
[ 3.822994] mousedev: could not register psaux device, error: -16
[ 3.828862] mousedev: PS/2 mouse device common for all mice
[ 3.835068] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.841714] input: samsung-keypad as /devices/platform/samsung-keypad/input/input1
[ 3.849008] usbcore: registered new interface driver xpad
[ 3.854141] usbcore: registered new interface driver usb_acecad
[ 3.859936] acecad: v3.2:USB Acecad Flair tablet driver
[ 3.865248] usbcore: registered new interface driver aiptek
[ 3.870700] aiptek: v2.3 (May 2, 2007):Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
[ 3.878596] aiptek: Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen
[ 3.886079] usbcore: registered new interface driver gtco
[ 3.891358] GTCO usb driver version: 2.00.0006
[ 3.895714] usbcore: registered new interface driver hanwang
[ 3.901530] usbcore: registered new interface driver kbtab
[ 3.906895] kbtab: v0.0.2:USB KB Gear JamStudio Tablet driver
[ 3.912736] usbcore: registered new interface driver wacom
[ 3.918092] wacom: v1.52:USB Wacom tablet driver
[ 3.923532] input: TSC2007 Touchscreen as /devices/virtual/input/input2
[ 3.930453] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 3.934713] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 3.940177] s3c_rtc_gettime() 2152-3-31 30:25:50
[ 3.945077] using rtc device, s3c, for alarms
[ 3.948909] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 3.956188] s5m-rtc s5m-rtc: rtc init
[ 3.958793] s5m_rtc_set_time: 2012/1/1 0:0:0(0)
)
[ 4.182187] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 4.188240] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[ 4.196291] device-mapper: uevent: version 1.0.3
[ 4.200521] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 4.208652] Bluetooth: HCI UART driver ver 2.2
[ 4.213058] Bluetooth: HCI H4 protocol initialized
[ 4.217829] Bluetooth: HCI BCSP protocol initialized
[ 4.222776] Bluetooth: HCILL protocol initialized
[ 4.227463] Bluetooth: HCIATH3K protocol initialized
[ 4.233031] cpuidle: using governor ladder
[ 4.237397] cpuidle: using governor menu
[ 4.240497] mshci: Mobile Storage Host Controller Interface driver
[ 4.246561] mshci: Copyright (c) 2011 Samsung Electronics Co., Ltd
[ 4.252807] clock source 0: sclk_dwmci (160000000 Hz)
[ 4.257764] dw_mmc dw_mmc: clock source 0: sclk_dwmci (160000000 Hz)
[ 4.264320] mmc0: Version ID 0x5342240a.
[ 4.268000] mjdbg: cmu_max_clcok:800000000
[ 4.272078] mjdbg: host->max_clk: 800000000
[ 4.276461] mmc0: FIFO WMARK FOR RX 0x11 WX 0x1. ###########
[ 4.284276] mmc0: MSHCI controller on samsung-mshci [dw_mmc] using IDMA
[ 4.289616] sdhci: Secure Digital Host Controller Interface driver
[ 4.296603] mmc0:mshci_set_clock, 400000@ration:4,11[mjdbg] cmu_set_clock: 400000
[ 4.303075] sdhci: Copyright(c) Pierre Ossman
[ 4.307470] s3c-sdhci s3c-sdhci.2: clock source 0: sclk_mmc (10666666 Hz)
[ 4.314207] mmc1: no vmmc regulator found
[ 4.318174] *******mmc0: inserted!!!!!******
[ 4.322597] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 4.329449] mmc0: cmd 52 response timeout error
[ 4.334986] wake enabled for irq 359
[ 4.337519] mmc0: cmd 52 response timeout error
[ 4.345276] s3c-sdhci s3c-sdhci.3: clock source 0: sclk_mmc (10666666 Hz)
[ 4.350619] sdhci_s3c_probe: set MMC_PM_IGNORE_PM_NOTIFY for mmc2 pm_flags
[ 4.351087] mmc0: cmd 8 response timeout error
[ 4.353932] mmc0: cmd 5 response timeout error
[ 4.355733] mmc0: cmd 5 response timeout error
[ 4.357536] mmc0: cmd 5 response timeout error
[ 4.359336] mmc0: cmd 5 response timeout error
[ 4.362184] mmc0: cmd 55 response timeout error
[ 4.365029] mmc0: cmd 55 response timeout error
[ 4.367874] mmc0: cmd 55 response timeout error
[ 4.370719] mmc0: cmd 55 response timeout error
[ 4.397654] sdhci_s3c_probe: set MMC_PM_KEEP_POWER | MMC_PM_WAKE_SDIO_IRQ for mmc2 pm_caps
[ 4.405913] mmc2: no vmmc regulator found
[ 4.410064] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 4.422376] usbcore: registered new interface driver usbhid
[ 4.423794] mmc0:mshci_set_clock, 50000000@ration:4,11[mjdbg] cmu_set_clock: 50000000
[ 4.434302] usbhid: USB HID core driver
[ 4.435392] mmc0: new high speed DDR MMC card at address 0001
[ 4.443914] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 4.444276] GPS: mt3326_gps_power: Switching GPS device on
[ 4.444284] GPS: mt3326_gps_power: ignore power control: 1
[ 4.444290] GPS: mt3326_gps_probe: Registering chardev
[ 4.444298] GPS: mt3326_gps_probe: major: 249, minor: 0
[ 4.444554] GPS: mt3326_gps_probe: Done
[ 4.445795] Samsung Audio Subsystem Driver, (c) 2011 Samsung Electronics
[ 4.445858] audss_init: RCLK SRC[busclk]
[ 4.485856] mmcblk0: p1 p2 p3 p4
[ 4.515062] *******mmc1: inserted!!!!!******
06] NET: Registered protocol family 29
[ 4.740052] mmc2: Internal clock never stabilised.
[ 4.744965] can: raw protocol (rev 20090105)
[ 4.749182] Bluetooth: RFCOMM TTY layer initialized
[ 4.753966] Bluetooth: RFCOMM socket layer initialized
[ 4.755064] *******mmc2: inserted!!!!!******
[ 4.763334] Bluetooth: RFCOMM ver 1.11
[ 4.767065] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.772359] Bluetooth: BNEP filters: protocol multicast
[ 4.775093] mmc2: Internal clock never stabilised.
[ 4.782473] NET: Registered protocol family 35
[ 4.787037] EXYNOS4X12: Adaptive Support Voltage init
[ 4.791807] EXYNOS4X12(SG): ORIG : 2 MOD : 0 RESULT : 2
[ 4.795280] mmc2: Internal clock never stabilised.
[ 4.801985] EXYNOS4X12(SG): ORIG : 2 MOD : 0 RESULT : 2
[ 4.807170] exynos4x12_set_abb:0x0, 0x0, 0x0, 0x0, 0x80000088
[ 4.812894] VFP support v0.3:
[ 4.815572] mmc2: Internal clock never stabilised.
[ 4.836738] mmc2: Internal clock never stabilised.
[ 4.840268] implementor 41 architecture 3 part 30 variant 9 rev 4
[ 4.846149] Registering SWP/SWPB emulation handler
[ 4.850924] DVFS : VDD_ARM Voltage table set with 2 Group
[ 4.856295] exynos4x12_volt_table[0]:1375000
[ 4.860547] exynos4x12_volt_table[1]:1350000
[ 4.861346] mmc2: Internal clock never stabilised.
[ 4.869687] exynos4x12_volt_table[2]:1300000
[ 4.873827] exynos4x12_volt_table[3]:1275000
[ 4.878080] exynos4x12_volt_table[4]:1212500
[ 4.882333] exynos4x12_volt_table[5]:1175000
[ 4.882512] mmc2: Internal clock never stabilised.
[ 4.891474] exynos4x12_volt_table[6]:1162500
[ 4.895614] exynos4x12_volt_table[7]:1162500
[ 4.899857] exynos4x12_volt_table[8]:1062500
[ 4.902699] mmc2: Internal clock never stabilised.
[ 4.909007] exynos4x12_volt_table[9]:1037500
[ 4.913148] exynos4x12_volt_table[10]:1025000
[ 4.917487] exynos4x12_volt_table[11]:1000000
[ 4.921827] exynos4x12_volt_table[12]:975000
[ 4.922889] mmc2: Internal clock never stabilised.
[ 4.930968] exynos4x12_volt_table[13]:975000
[ 4.935109] exynos4x12_cpufreq_init:topeet scp
[ 4.939900] [ 302612 ] Memory Type Undertermined.
[ 4.944230] DVFS : VDD_INT Voltage table set with 2 Group
[ 4.945105] mmc2: Internal clock never stabilised.
[ 4.965287] mmc2: Internal clock never stabilised.
[ 4.988891] mmc2: Internal clock never stabilised.
[ 5.005213] exynos4_integrated_dvfs_hotplug_init, max(1400000),min(200000)
[ 5.012495] mmc2: Internal clock never stabilised.
[ 5.014184] regulator_init_complete: VDD18_MIPI: incomplete constraints, leaving on
[ 5.014622] regulator_init_complete: VDD10_MIPI: incomplete constraints, leaving on
[ 5.015060] regulator_init_complete: VDD18_2M: incomplete constraints, leaving on
[ 5.016780] regulator_init_complete: vdd_int range: incomplete constraints, leaving on
[ 5.017217] regulator_init_complete: vdd_arm range: incomplete constraints, leaving on
[ 5.017654] regulator_init_complete: vdd_mif range: incomplete constraints, leaving on
[ 5.017991] USB_DEVICE_ATTACHED
[ 5.085626] mmc2: Internal clock never stabilised.
[ 5.115066] *******mmc2: inserted!!!!!******
[ 5.124082] exynos_usb_Device: Exynos USB Device Driver
[ 5.127846] value1 = 1, value2 = 0, type = 0x2
[ 5.137284] ==ft5x0x_ts_init: reset==
[ 5.165079] *******mmc2: inserted!!!!!******
¤JRead: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 5.829695] <<-GTP-INFO->> Guitar reset
[ 6.056221] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -6!
[ 6.061812] <<-GTP-ERROR->> GTP i2c test failed time 2.
[ 6.081078] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 6.087879] <<-GTP-INFO->> Guitar reset
[ 6.315956] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -6!
[ 6.321686] <<-GTP-ERROR->> GTP i2c test failed time 4.
[ 6.340090] <<-GTP-ERROR->> I2C communication ERROR!
[ 6.343649] Goodix-TS: probe of 3-005d failed with error -1
[ 6.351070] s5m_rtc_read_time: 2012/1/1 0:0:3(0)
[ 6.354260] s3c_rtc_settime() 2012-1-1 0:0:3
[ 6.358589] s5m_rtc_set_time: 2012/1/1 0:0:3(0)
[ 6.390161] s5m-rtc s5m-rtc: setting system clock to 2012-01-01 00:00:03 UTC (1325376003)
[ 6.398530] FIMC0 registered successfully
[ 6.402559] FIMC1 registered successfully
[ 6.406560] FIMC2 registered successfully
[ 6.410536] FIMC3 registered successfully
[ 6.413941] S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
route: SIOCADDRT: No such process
Done
Please press Enter to activate this console. [ 28.001847] CPU3: shutdown